Rheem Heat Pump Installation Nationwide | Dalton Heating & Air Houston

Rheem Heat Pump Installation in Houston: What to Know First

We install Rheem heat pump systems across Houston as an independent Rheem service provider, and most jobs go from first call to running system within 3 to 7 days once equipment is selected. A Rheem heat pump installation in Houston typically runs $3,500 to $7,500 depending on the model line, the size of your home, and what your existing ductwork and electrical setup can support. The price is in writing before any work starts, and every installation carries the same full-year written guarantee we put on every job we do. If you own a Rheem and you’re weighing repair against replacement, or you’ve already decided it’s time for a new heat pump, call (903) 494-7686 and we’ll give you a straight answer.

Call (903) 494-7686

How Rheem Products Fail – and How We Fix Them

• Reversing valve sticking on RP14 and RP15 series units. The reversing valve is the part that switches a heat pump between cooling and heating. In Houston, where systems run cooling for eight months and then flip to heat on the first cold snap, valves that sit in one position too long can stick. The symptom is a unit that cools fine but won’t heat, or heats but won’t cool. We don’t just replace the valve and walk off. We cycle the system through both modes a dozen times and verify the valve shifts every single time before we call the job done.
• Defrost board failures on RP16 and RP17 two-stage units after heavy rain or hurricanes. Houston humidity is the real test of a heat pump’s defrost cycle. We see defrost boards on two-stage Rheems fail after prolonged wet weather, leaving the outdoor coil iced over in winter and the system locked into defrost mode. The board controls the defrost timer and the reversing valve signal. We test the sensors first, because a $20 temperature sensor often gets blamed on a $300 board. If the board is done, we install the OEM replacement so the warranty stays intact.
• Compressor contactor pitting on Prestige series systems near the Energy Corridor. The electrical load on older equipment out near the Energy Corridor in summer is punishing, and contactors – the electrical switches that engage the compressor – take the hit. Pitted contactor points cause intermittent short-cycling, and short-cycling kills compressors. When we’re on a Rheem install and we see a contactor with burn marks, we replace it on the spot. A $40 contactor beats a $2,000 compressor replacement.
• OEM vs aftermarket parts decisions on Classic and Value series units. Rheem’s Classic and Value lines are the budget-friendly options, and owners sometimes pressure us to use the cheapest aftermarket parts available to keep costs down. We’ll tell you straight: for electrical components and safety controls, OEM is the only way we go. For universal parts like capacitors and contactors where Rheem doesn’t make the part anyway, quality aftermarket is fine. We’ll put the part options and prices in writing so you decide with full information.
• Improper refrigerant charge on existing Rheem units before installation. Before we install any new equipment, we check the charge on the existing system. Houston heat hides low refrigerant because the system still feels cool at the vent, but it’s running at 70% capacity and burning extra electricity. If your old Rheem was undercharged, we want to know why before we tie new equipment to existing lines. A leak in a line set will kill a new heat pump just as fast as it killed the old one.

Our Rheem Heat Pump Installation Process

1. 1
   You call, a live person answers. No voicemail queue, no callback window. We take your information, hear what the current system is doing, and set a window we actually keep. Marco Benitez sets the dispatch schedule himself, and if a tech is running late, you hear from us before the window passes.
2. 2
   We diagnose the existing system. Our tech checks refrigerant charge, airflow, duct condition, electrical service, and the breaker panel. We’re looking for what killed the old unit, not just what we’re replacing. Undersized ductwork in a Houston attic can strangle a brand-new heat pump, and we’d rather tell you now than install a system that never works right.
3. 3
   We give you a written price before any work starts. You’ll see the equipment, the labor, the electrical work, the line set work, everything. That price does not move at the door. It’s The Garrison Standard, and we’ve been holding to it since 2003.
4. 4
   We install the Rheem heat pump by the book. New equipment goes in, electrical gets connected to code, the line set gets flushed or replaced, and the system gets drawn down and leak-tested before we add refrigerant. Every install gets a full nitrogen pressure test. No shortcuts, no skipped steps.
5. 5
   We test, verify, and walk you through it. We cycle the system through cooling and heating, verify defrost, verify thermostat wiring, and check temperature differential across the coil. Then we show you the thermostat settings, explain what to watch for, and hand you the written guarantee.
6. 6
   We leave the site clean and stand behind the work for a full year. The 365-Day Done Right Promise covers every install. If something isn’t right in that first year, we come back at no charge. Full stop.

What Rheem Heat Pump Installation Costs in Houston

Here are the dollar ranges we quote on Rheem heat pump installations in Houston:

• Rheem Classic series (RP14) heat pump installation: $3,500 – $5,000 depending on size and existing ductwork
• Rheem RP16 two-stage heat pump installation: $4,500 – $6,500
• Rheem Prestige series (RP17) variable-speed installation: $6,000 – $7,500

What moves the number: the condenser tonnage your home actually needs, whether your existing line set can be reused, whether your electrical panel has room for the breaker, and how much duct modification is needed. A two-story Houston home with a 4-ton load is going to land higher than a single-story ranch on a 2-ton load. We don’t pad the quote and we don’t play games with the final price. Call (903) 494-7686 for a free estimate with the number in writing before anything gets installed.

Why Houston Homeowners Call Dalton Heating & Air Houston for Rheem Work

We’re a Garrison Partners company, which means every job runs on The Garrison Code: show up inside the window, put the price in writing before starting, do the work by the book, leave the site clean, and stand behind it for a full year. That’s not marketing language. It’s the operating standard we’ve held since 2003. Our techs are factory-trained on Rheem equipment but we also service Carrier, Trane, Lennox, Goodman, York, Daikin, Bryant, and American Standard, so if the best solution for your home isn’t a Rheem, we’ll tell you that. Every call is answered by a live person, every tech is background-checked and uniformed, and every job ends with a written guarantee. If the work fails in the guarantee period, we come back at no charge. That’s the whole point of The Garrison Standard.

FAQs